These adapters are designed so you can use a variety of male caps on cans with male valves.

Blue and Grey adaptors are slightly different sizes to suit different brands of cans.

Grey adapters have been tested to work well on Aussie Export cans and seem to fit well on other Australian brands of spray paint.

Blue adapters are better suited to American brands like Rustoleum.

They can also be used as a mixing cap for transferring paint from male to male cans.

Made in USA

This cap fits all popular female can and comes with a detachable spigot ( Stem ) that allows it to fit onto cans which have a 4mm wide spigot.

This cap has a perfectly round dot with fast output and ability to paint tiny details from 3mm to outlines around 20mm which makes it extremely versatile.

The extended profile allows you to get into tighter spots with more accuracy and offers extreme control via our original design.

PATENT PENDING *This product is solvent resistant and designed to be reused and cleaned.

Like a mini extinguisher this cap goes hard! The extended 14cm tube allows you to reach up to 4m high from the ground.

Easy to clean with any solvent base liquid or spray cleaning can (Like MTN Solvent) and is reusable.

Not compatible with adapters or low pressure cans.

• Achieve incredible details with 2mm / 0.08" thin lines!
• Built-in 45ml / 1.52fl.oz. reservoir
• Fits on every spraycan!
• Work on minimum space!
• Easy to use!
• Easy to clean!
• No mess anymore!
• Patented!
• Don't wait to level-up your art!

How should I use my TINYPINK?

Shake your spray can very well before you attach the TINYPINK stencil cap! Best to use it with a standard or original cap (black/white) or a skinny cap! Then just click the TINYPINK on the big fold on the upper end of your spray can! Finally, press down the cap! If no paint comes through the whole turn your cap slightly to the right or left.

Don't shake the can while there is paint in the TINYPINK's reservoir! Paint will splatter! If you can't avoid shaking it, you can try putting a piece of cloth in the reservoir! This will be like a sponge and will prevent the paint running out. Of course you have to replace the cloth with a new one from time to time!

Empty the reservoir regularly!

Which cap should I use together with the TINYPINK stencil cap?

We recommend standard or original cap (black/white). Also (ultra) skinny caps work fine! With fat caps you will waste far more paint.

You can also try needle caps! These will provide much more saturated lines in combination with the TINYPINK stencil cap but with no splatters like you know it from junkie caps!

TINYPINK stencil cap - needle cap

How can I achieve 3mm / 0.12“ to 5mm / 0.20“ thick lines?

Just widen the hole with a 3mm / 0.12“ to 5mm / 0.20“ drill according to your preferences!

TINYPINK stencil cap - drill TINYPINK stencil cap - 3-5mm drill

The TINYPINK doesn‘t work! No paint comes through the hole!

The reason is mostly because the spray pattern of a cap is more like a ring (no filled centre) and not like a dot. So please try to turn the cap a little bit to the left or right so that the "ring" hits the hole!

Or try a needle cap! This should work for sure and you will get more saturated lines as with skinny caps!

TINYPINK stencil cap - turn cap TINYPINK stencil cap - needle cap

The hole clogs very quickly!

The TINYPINK comes with a 2mm / 0.08“ hole to achieve 2mm / 0.08“ thin lines! If it clogs to fast please stick the included nail through it to open it again.

We also recommend to use acetone spray (Montana Cans Cap Cleaner, Loop Acetone Spray, MTN, etc.) with a needle cap to blast residual paint out of the hole!

Another option is to widen the whole with a 3mm / 0.12“ to 5mm / 0.20“ drill! Just customise your TINYPINK to your preferences. The wider the whole, the thicker the lines, the less likely it will clog.

TINYPINK stencil cap - nail TINYPINK stencil cap - acetone spray

How long will the TINYPINK last?

It's like with all things in life: the better you treat your stencil cap the longer it will last!

Clean your TINYPINK properly! Please have a look at section „How should I clean it?“ to learn about the right maintenance!

How should I empty the reservoir?

simply turn it upside down and let the paint run out at one corner.

Don't take off the plug to empty the reservoir or you will have a big mess! Remove it only for cleaning purposes after the reservoir was emptied!

TINYPINK stencil cap - empty reservoir

Why doesn't the paint run into the reservoir but down the outside of the stencil cap?

There is a slit right under the hole. Make sure it isn't clogged with paint! Open it with the included nail or acetone!

My plug shrinked! / My plug doesn't fit into the reservoir anymore!

The most common reason is that the plug has had paint on it for too long or it has been soaked in acetone for too long.

You should also not leave the TINYPINK in the blazing sun for too long at temperatures above 40°C / 100°F! This can cause the material to soften and shrink! If your plug is no longer tight, simply secure it with a piece of tape!

How to clean the TINYPINK at the end of a day?

If your TINYPINK has a lot of dried paint on it you can put it in an acetone bath. Take a screw-top jar, put (only!) the pink part of your stencil cap inside with some acetone, close it with a lid, and shake it. Let it rest there for an hour. Repeate shaking is recommend! Take the TINYPINK out and scrub off the paint which wasn't dissolved with a toothbrush or similar.

Like said before, never let the black plug rest in an acetone bath! It can be damaged because the solvent in the paint can react with the rubber. Just wipe of the paint with a cloth dunked in acetone or use an acetone spray!

The OG Stencil Cap™ by SWANK ONE

Pioneered by West Coast graffiti writers, the original OG Stencil Cap is the first and finest line cap adapter made for today's serious aerosol artist. The OG Stencil Cap is the first professional iteration of this adapter developed for manufacturing by writer SWANK ONE, this game-changing tool gives you the power to spray incredibly thin, precise lines and achieve the finest details like never before.

Stencil Caps are used to create ultra fine lines. Attach them over your regular skinny nozzle and the small hole will only let a small amount of the paint through, creating super fine lines on your artwork. Keep them clean and you can reuse for years.

• Available with hole size 1mm, 2mm and 3mm

• Precision-cut venting for consistent spray flow

• Easy to clean / solvent resistant

• Designed for repeat use in professional production work

• Made in USA

For the best output use High pressure cans, like the MTN Megas.

Wider, faster with comfort to get your painting done in half the time.

Premium engineer grade plastic and re useable.

Cleans easily in acetone and regular solvent.

The design and comfort are 2nd to none and offer an unparalleled experience.

The Aqua/Black - Medium Touch ( Less bounce with more direct flow )

Perfect for a range of nozzles Medium to thin.

The Medium Touch ( Aqua ) Actuator retains rigidity and offers slightly more bounce in it’s characteristic.

Best used on softer valve systems to help avoid strain while offering great control and half nozzle pressure consistency.

Night Quill has been developed to aid, assist and further the art forms utilising spray paint. Night Quill utilise technical and ergonomic design to manufacture a new era of art & graffiti implements.

Night Quill's goal is to bridge the gap with skill level as a beginner and offer products that give confidence and assist in the most creative artistic outcome. Having such tools will give people experiencing muscle, joint or tendon problems a chance to continue their art practice and career path.

The Night Quill actuator gives you the opportunity to paint comfortably with both hands for a prolonged amount of time when strain sets in.

Night Quill isn’t a throw away product, but a tool to be taken care of and reused many times.

There are 3 colour coded Night Quills available with varying Bounce - soft, medium or hard Touch.